|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
| Re: Sad But True, Lamont... [message #86930 is a reply to message #86909] |
Wed, 20 June 2007 09:06   |
LaMont
Messages: 828
Registered: October 2005
|
Senior Member |
|
|
>>MF Ch 2 =3D Mono Input/Snare
>>>MF Ch 3 =3D Mono Input/Hat
>>>MF Ch 4 =3D Mono Input/Cowbell & digital cowbell sample triggers
>>>MF Ch's 5&6 =3D Stereo Input/OH's
>>>MF Ch's 7&8 =3D Stereo Input/Drum Room-Ambience Mics
>>>MF Ch's 9&10 =3D (SPDIF/Not used in this scenario)
>>>MF Ch's 11 to 14 =3D ADAT (Lightpipe) inputs used for 4 tom mics.
>>>
>>>... and the only OUTputs you have assigned are:
>>>MF Ch's 1&2 (OUTPUTS) =3D main monitors
>>>
>>>OK, so that wipes out ALL the inputs except for SPDIF in the
>>>first Multiface, yes? All the other inputs would have to be
>>>routed through the 2nd Multiface in this scenario... here's the
>>>thing... when you get to mixdown & external EFX routing, let's
>>>say you want your VST connections to look like this on your
>>>first (Master!!!) Multiface - i.e the same one as above:
>>>
>>>MF Ch's 1&2 OUTPUTS =3D main monitors (no change there)
>>>MF Ch 3 OUTPUT =3D send to external EFX/Distressor on vox track
>>>MF Ch 3 INPUT =3D return from external EFX/Distressor on vox track
>>>MF Ch 4 OUTPUT =3D send to external EFX/Massenburg EQ on kik
>>>MF Ch 4 INPUT =3D return from external EFX/Massenburg EQ on kik
>>>MF Ch's 5&6 OUTPUTS =3D send to external Lexi 480L, Engine "A"
>>>MF Ch's 5&6 INPUTS =3D return from external Lexi 480L, Engine "A"
>>>MF Ch's 7&8 OUTPUTS =3D send to external Lexi 480L, Engine "B"
>>>MF Ch's 7&8 INPUTS =3D return from external Lexi 480L, Engine "B"
>>>MF CH's 9&10 OUTPUTS =3D SPDIF to Quantec Yardstick IN's/Sends
>>>MF CH's 9&10 INPUTS =3D SPDIF to Quantec Yardstick OUTS/Returns
>>><lightpipes not used in mixdown in this example>
>>>
>>>Quite a bit different routing scenario than the one you used for
>>>tracking, yes? I suspect what's happening is that you're not
>>>saving your VST connections routing - if that's the case, every
>>>time you open up a project it'll take you to the last "saved"
>>>version, including any routing changes you've made & saved,
>>>but NOT any routing changes you've made, but not saved!
>>>
>&g
|
|
|
|
| Re: Sad But True, Lamont... [message #86931 is a reply to message #86930] |
Wed, 20 June 2007 09:21 |
EK Sound
Messages: 939
Registered: June 2005
|
Senior Member |
|
|
t;>You can save these routing/patching changes in one of two ways:
>>>
>>>1.) set up all your routing for your patching & external EFX,
>>>and make sure you save the project again once you do that
>>>(either under a new project name or just overwrite what you've
>>>got... I tend to save under a new name in case I fuck anything
>>>up - or simply hate what I've done - and need to go back :) )
>>>
>>>2.) Save your routing scenarios in the "VST Connections"
>>>dialogue... there's an option that let's you save those...
>>>you could go from:
>>>"ScreamingOkapis-SongOfWorldPeace-BasicTrackRouting", to...
>>>"ScreamingOkapis-SongOfWorldPeace-OverdubRoutingA", to...
>>>"ScreamingOkapis-SongOfWorldPeace-VocalOverdubs", to...
>>>"ScreamingOkapis-SongOfWorldPeace-MixdownRoutingA", to...
>>>"ScreamingOkapis-SongOfWorldPeace-MixdownRoutingB"
>>>
>>>Now, it's true I have SX3 and you have C4, but I would bet it's
>>>the same basic idea. Got it? Kewl?
>>>
>>>Let us know if that works for you.
>>>
>>>Neil
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>
>>>"DJ" <animix _ at _ animas _ dot _ net> wrote:
>>>
>>>>Every time I close a project and then reopen it, various patches to =
my
>>>>external gear are disabled.....especially prevalent on the inputs, =
but not
>>>
>>>>always, and sometimes the outputs are reassigned to different ones. =
I never
>>>
>>>>know what I'm going to be faces with when I recall a project. =
Sometimes
>>>
>>>it=20
>>>
>>>>takes me 10-15 minutes just hunt everything down to repatch.
>>>>
>>>>This really sucks........and I mean to the point that I'm about to =
kick
>>>
>>>this=20
>>>
>>>>damn thing out the window. Does Nuendo do this too? I need to be =
able to
>>>
>>>>save a project with AD/DA's assigned to external processors and be =
able
>>>
>>>to=20
>>>
>>>>recall it.......CONSISTENTLY!!!. This **FUCKING POS** is about to =
PISS ME
>>>
>>>>OFF!!!!!=20
>>>>
>>>>
>>>
>>
------=_NextPart_000_0359_01C7C5ED.0AC879A0
Content-Type: text/html;
charset="iso-8859-1"
Content-Transfer-Encoding: quoted-printable
<!DOCTYPE HTML PUBLIC "-//W3C//DTD HTML 4.0 Transitional//EN">
<HTML><HEAD>
<META http-equiv=3DContent-Type content=3D"text/html; =
charset=3Diso-8859-1">
<META content=3D"MSHTML 6.00.6000.16414" name=3DGENERATOR>
<STYLE></STYLE>
</HEAD>
<BODY>
<DIV><FONT face=3DArial size=3D2>I called Steinberg USA. They called =
Germany. I got=20
the following in an e-mail:</FONT></DIV>
<DIV><FONT face=3DArial size=3D2></FONT> </DIV>
<DIV><FONT face=3DArial size=3D2><EM>Maybe the 2x audio cards are =
cascaded=20
differently each time on booting up the machine? This would explain how =
the=20
busses are set wrong in C
|
|
|
|
The PARIS Forums
Search
Help
Members
Register
Login
Home
